6 schedule 40 stainless steel pipe dimensions

All pipes, regardless of type, are typically featured through two non-dimensional numbers. The first of which is a nominal pipe size (NPS) that is based on inches and relates to the inside diameter. The second of these numbers, referred to as “schedule” (Sched. or Sch.), represents the wall thickness. So to ensure you select the right pipe for your next project, make sure to familiarize yourself with both of these essential aspects of pipe size and tolerance Management.

Delving Deeper into the Dimensions & Weight of Pipes

The Pipe Schedule Number is a tool that dictates the thickness of pipes. As these numerical values increase, so does the wall thickness that encases pipes. In doing this, the Schedule number acts as a kind of failsafe for understanding and distinguishing different pipe sizes.

Steel pipes are named by their nominal trade names, which are remotely related to their actual measurements. For example, a 2-inch galvanized pipe displays an inside measurement of 2 1/8 inches and an outside measurement of 2 5/8 inches. In the world of plumbing, this size is called Nominal Pipe Size (NPS) or Nominal Bore (NB). This distinctive legal term ‘nominal’ specifies pipe diameters with an arbitrary numerical figure (e.g., a 2-inch nominal steel pipe entails varied types of steel pipes with the sole requirement being an outer diameter of 2.375 inches (60.3 mm)).

6-inch Schedule 40 pipes are available in a total of 12 units, and this is evidenced in the below-provided table that succinctly outlines the relevant measurements:

The diameters of the exterior, interior, and walls of a given item can be measured and compared using the Outside Diameter, Inside Diameter, and Wall Thickness measurements, respectively.

The dimensions read as follows: a length of 6.625 inches (168.3 millimeters), a width of 6.065 inches (154.2 millimeters), and a thickness of 0.280 inches (7.11 millimeters).

With a total length of 6.765 inches (172.0 mm), and a height of 6.065 inches (154.2 mm), the thickness arrives at 0.300 inches (7.62 mm).

The dimensions of the item measure 6.875 inches in height, 6.065 inches across, and 0.318 inches in thickness.

The sleek dimensions of the design are truly captivating, measuring 6.965 inches (177.0 mm) by 6.065 inches (154.2 mm) with a depth of 0.334 inches (8.47mm).

7,000 inches (177.8 mm), 6,065 inches (154.2 mm), and 0.340 inches (8.64 mm) make up the measurements.

Measuring an impressive seven and one eighth inches, with a width measuring six and sixty-five hundredths inches and thickness of just over three and a half tenths of an inch, this object offers angled dimensions that take visual appeal to the next level.

Measuring 7.625 inches (193.7 millimeters) in height, the shape stands 6.065 inches (154.2 millimeters) across and is 0.438 inches (11.11 millimeters) thick.

The size of the wall of a pipe can be determined by examining its assigned Pipe Schedule Number. Rising numerically, the higher this number is, the thicker the pipe’s wall. For example, a Pipe Schedule Number of 80 indicates a thicker wall than one of 40.

Popular Size Grades of Schedule 40 Piping: | Nominal Pipe Size | Outer Diameter | Grade | | —————- | ————— | —— |

A nominal 1/8th of an inch is equal to 0.405 inches, which translates to 10.29 millimetres – all 40 of them to be precise.

A quarter inch, which is equivalent to 0.540 inches or 13.72 millimeters, can be found in roughly 40 different varieties.

The nominal measurement of 3/8 inches translates to 0.675 inches, or 17.15 millimeters, while 40 is the equivalent.

The nominal width of this item is half an inch, while its actual width is 0.840 inches or 21.34 mm. With a 40 degree angle, it can be applied to a variety of projects.

A nominal dimension of three-fourth of an inch translates to one-thousand-fifty in terms of its inches, and twenty-six-point-six seven millimeters in width. It has a total of forty elements attached to it.

The size of one (1) unit measures one point three one five inches (1.315″), corresponding to a length of thirty-three point four zero millimeters (33.40 mm). In total, this size is composed of forty individual lengths of measurement.

With a width measuring 1-1/4 inches (nominally), the outer diameter is approximately 1.660 inches, equating to 42.16 millimeters, and the gauge is 40.

A nominal measurement of 1 and a half inches is equivalent to 1.900 inches (or 48.26 mm); this parallel measurement holds an accuracy count of 40.

Two inches (2 in) as an approximate width, followed by a slightly wider 2.375 inches (or 60.33 mm) and concluded with a quantity of 40 – these dimensions and quantity make up the figure laid out before us.

The dimensions of the product are 2 and a half inches (nominal), with an exact measurement of 2.875 inches (73.02 mm). Its weight is forty units.

The nominal measurement of three inches translates to three-point-five hundred inches, or eighty-eight point ninety millimeters, as denoted in the 40 designation.

The nominal diameter of 3 1/2 inches converts to 4.000 inches, or a circumference of approximately 40 inches.

With a nominal size of four inches and a diameter of 4.500 inches (114.30 mm), the item has a thickness of forty units.

The width measures five inches in its nominal form, yet expands slightly to five and a half inches, or 141.30 millimetres, with a 40-level grade.

The original measure was 6 inches in nominal value but it extended to 6 and 5/8 inches (equivalent to 168.28 millimeters) for a total of 40 pieces.

Scheduling 40 is the go-to pipe type for the majority of projects.

Related Product